混流泵

（二）泵蓋是泵與進水管相連的零件，其端面與葉輪之間留有規定的軸向端面間隙（在消除軸承軸向活動間隙以后，保持規定的軸向間隙）。間隙過小產生磨擦，過大則會導致泵內壓力水回流，使泵的效率降低，通過增減調整紙墊達到規定的間隙。

II.  Pump cover is

the part connected with water inlet pipe.There is an stated axial end face gap

between its end

face and

impeller(Keep the stated axail gap after removing the bearing axial movable

gap).Friction will be

produced if

the gap is too small, contrary, if the gap is too large, the pressure water in

pump will reflux which

makes the

feeiciency reduced.Adjust the paper washer and make the gap be stated one.

（二）開車前準備：

1、檢查地腳螺栓的堅固情況。

2、檢查傳動皮帶松緊程度及安裝設備是否安裝妥善。

3、檢查進、出水管是否進氣、漏水。

4、檢查填料松緊是否適宜。

5、檢查電動機和水泵軸心線是否在同一直線上，直聯時，電動機旋轉方向是否符合泵的旋轉方向。

6、檢查泵內有無障礙，軸是否卡住，用手轉動應輕無雜音。

II. Preparation Before Starting

1. Check the foundation bolts if they are firm.

2. Check the degree of tightness of drive belt and check the

installation if it is suitable.

3.Check the water–in and outpipes if they are leaking water and air.

4.Check the degeree of tightness of padding if it is suitable.

    5.Check the

motor and pump axile lead if they are in the same line and check the direction

of rotation of motor if it is the same with the rotation direction of pump.

    6.Check the

pump if there are barriers , if the axile locks, there should be no noises when

turing it by hand.

4、水泵使用后一定要注意保養，比如說當水泵用完后要把水泵里的水放干凈， 是能把水管卸下來然后用清水沖洗。

5、水泵上的膠帶也要卸下來，然后用水沖洗干凈后在光照處晾干，不要把膠帶放在陰暗潮濕的地方。水泵的膠帶一定不能沾上油污，更不要在膠帶上涂一些帶粘性的東西。

6、要仔細檢查葉輪上是否有裂痕，葉輪固定在軸承上是否有松動，如果有出現裂縫和松動的現象要及時維修，如果水泵葉輪上面有泥土的也要清理干凈